To choose a brass vessel sink, match three things: the bowl size to your counter, the bowl height to your vanity, and the faucet to the rim. Most bathrooms suit a 12 to 16 inch bowl, powder rooms suit 8 to 10 inches, and an 18 inch bowl needs a wide counter. Because a vessel sink sits on top of the counter, plan for a lower vanity and a tall vessel faucet or a wall-mounted tap so the rim lands at a comfortable washing height.
In this article
- What size brass vessel sink do you need?
- Should you choose a round or oval bowl?
- Hammered, smooth or engraved: which brass finish suits you?
- How much does a brass vessel sink cost?
- How tall should the vanity be under a vessel sink?
- What faucet works with a brass vessel sink?
- How is a brass vessel sink installed?
- What are the downsides of a vessel sink?
- How do you care for an unlacquered brass vessel sink?
- FAQ
What size brass vessel sink do you need?
Start with your counter, not the sink you love most. A vessel bowl needs room around it for the faucet, for wiping and for your elbows.
All our sizes are measured across the inside of the basin, excluding the rim. The outside of the bowl is a little larger, so leave a margin.
| Bowl size (inside) | Best for | What to check |
|---|---|---|
| 8 to 10 in | Powder rooms, narrow and compact vanities | Faucet reach, since a small bowl leaves little room behind it |
| 12 to 14 in | Most guest and family bathrooms | Counter depth with the faucet behind the bowl |
| 16 to 16.5 in | Single primary vanities, shallow wide bowls | Bowl height and splash zone |
| 18 in | Statement pieces on a wide counter | Space on both sides and behind the bowl |
A quick way to test fit: cut a paper circle or oval at the outside size of the bowl and set it on your counter where the sink will go. Then mark where the faucet will sit. If the paper crowds the back edge or the faucet, step down a size.

Round and hand-hammered in an aged brass finish, in five diameters from 8 to 16 inches, each about 5.5 inches tall.
Should you choose a round or oval bowl?
Round bowls are the classic choice and look the same from every angle, which suits a centered single vanity. They take up equal space front to back and side to side, so on a shallow counter a round bowl can push the faucet against the wall.
Oval bowls are longer than they are deep. Our Hammered Oval Brass Vessel Sink, for example, runs from 10 x 7 inches up to 18 x 12 inches inside the basin. That shorter front to back measurement leaves more room for a deck-mounted faucet on a shallow counter, and the long shape gives you more elbow room for washing your face.
Profile matters too. A deep bowl contains splashes better, while a wide, shallow bowl like our 16.5 inch round countertop sink sits lower and pairs naturally with a wall-mounted faucet.
A deep oval bowl on a round pedestal foot, polished bright gold, from 10 x 7 to 18 x 12 inches inside the basin.
Hammered, smooth or engraved: which brass finish suits you?
The surface of the bowl changes the whole feel of a vanity, so it is worth deciding on finish before you fall for a shape. Our brass vessel sinks come in five main looks:
- Hand-hammered and bright. Polished brass with hammer marks that catch the light, like the Hammered Round and Hammered Oval sinks. It starts golden and mellows over time.
- Aged. A darker, warmer tone from day one, like the Meknes. Choose this if you want the look of an old sink straight away.
- Smooth or brushed. A quiet, clean surface, like the 16.5 inch round countertop sink or the satin Brushed Brass Round Vessel Sink. These suit modern and minimal bathrooms.
- Engraved. Hand-cut Moroccan swirls or vine bands on the outside of the bowl, like the Engraved Brass Pedestal and Vine Engraved sinks. This is the most decorative choice and the one that reads most clearly as handmade.
- Two-tone. A polished brass interior with a contrasting outside, such as the bronze exterior of the Bronze and Brass Round Vessel Sink or the black and white Scallop sink.
If you want the easiest finish to live with, choose hammered. In our experience the hammer texture hides small irregularities and water spots far better than a smooth surface, which shows every mark.
A simple rule: start bright if you love watching brass change, and start aged if you want it to look settled from the first day. For more on how each finish ages, see unlacquered vs lacquered brass.
How much does a brass vessel sink cost?
Across our current catalog, brass vessel sinks run from $79 for an 8 inch Meknes to $475 for an 18 inch engraved pedestal bowl. Three things move the price: the size of the bowl, how much decoration it carries, and whether you add a matching drain.
| Inside size | The Meknes (aged, in stock) | Hammered Round (sink only) | Engraved Brass Pedestal |
|---|---|---|---|
| 10 in | $131 | $125 | $131 |
| 14 in | $240 | $246 | $297 |
| 16 in | $368 | $329 | $396 |
| 18 in | Not offered | $393 | $475 |
Prices are as listed today and can change, so check the product page before you order. At the same 14 inch size, the engraved bowl costs $51 to $57 more than the two plainer bowls, which reflects the extra hand work on the outside. A matching push-up drain adds $34 to the Hammered Round and $31 to the 16.5 inch round countertop sink.
When you compare prices elsewhere, check that you are comparing the same thing. Our sizes are the inside of the basin, so a bowl listed by its outside size elsewhere will hold less water than the same number here.
How tall should the vanity be under a vessel sink?
A vessel sink adds its own height on top of the counter, so the rim ends up higher than on a drop-in or undermount sink. Design guides commonly advise picking a shorter vanity so that the vanity and vessel together come to about 36 inches or a little lower.
The math is simple: vanity height (including the countertop) plus bowl height equals rim height. Here is how it works with two of our sinks.
| Sink | Bowl height | On a 30 in vanity | On a 34 in vanity |
|---|---|---|---|
| The Meknes Brass Vessel Sink | About 5.5 in | Rim at about 35.5 in | Rim at about 39.5 in |
| Round Brass Countertop Vessel Sink, 16.5 in | About 4.5 in | Rim at about 34.5 in | Rim at about 38.5 in |
If you are keeping an existing vanity, a lower, shallower bowl is the easier fit. If you are buying a new vanity, choose the sink first, then pick the cabinet height that brings the rim to where you like it.

A smooth, wide bowl about 4.5 inches tall, an easy match for a wall-mounted faucet. Optional push-up drain.
What faucet works with a brass vessel sink?
A standard bathroom faucet is too short, because its spout would end up at or below the rim. You have two good options: a tall deck-mounted vessel faucet set behind or beside the bowl, or a wall-mounted faucet with the supply lines in the wall.
To size a deck-mounted faucet, faucet maker VIGO suggests adding the countertop thickness, the bowl height and a comfortable clearance above the rim to find the spout height you need. Aim the stream at the drain rather than the side of the bowl, and keep the spout only a few inches above the rim, since a long drop splashes more.
Wall-mounted faucets are a natural partner for wide, shallow bowls because you can set the spout at exactly the right height. They need to be planned before the wall is closed, so talk to your plumber early. For finish ideas, see our guide to the best faucet finishes for a brass or copper sink.

Before you order, also check the drain. Several of our bowls, including the Hammered Round Brass Vessel Sink and the 16.5 inch round countertop sink, have a 1.63 inch drain opening and offer a matching push-up drain, so the drain finish matches the bowl.
Also check for an overflow. Some of our basins have an overflow hole and some do not, and drains are made for one or the other. Check the product page or ask us which yours has, then buy a drain that matches.
A deep round bowl with a thin rolled rim and small foot, in 10, 14, 16 or 18 inches, with an optional push-up drain.
How is a brass vessel sink installed?
A vessel sink is one of the simplest sinks to install, because it sits on top of the counter instead of in a large cutout. The order of work matters more than any special skill:
- Settle the vanity height and faucet first. Do the rim height math above and choose a deck-mounted or wall-mounted faucet before anyone drills.
- Mark the drain position. Center the bowl where you want it, then mark the drain so the bowl sits square to the wall and leaves room for the faucet.
- Cut the drain hole to suit the drain. Several of our bowls have a 1.63 inch drain opening, so match the counter hole to the drain you are using.
- Fit the drain and set the bowl. Seal the drain as its maker instructs, then bed the bowl on a thin bead of clear silicone around the base.
- Connect the trap and let it cure. Hook up the P-trap, wipe away excess silicone, and leave the sealant to cure for the time on its label before running water.
We recommend a licensed plumber for the drain and supply connections, especially for a wall-mounted faucet, which needs pipes inside the wall.
The mistake we see most often: setting the bowl and the faucet out of line with each other. If the spout does not point at the drain, water hits the side of the bowl and splashes. Before the silicone goes down, set the bowl in place, hold the faucet where it will sit and check that the stream will land on the drain. If you are fitting an undermount sink elsewhere in the house, the other common mistake is cutting the counter opening to the wrong size, so measure it against the sink itself. Our undermount sink install guide covers that.
What are the downsides of a vessel sink?
Vessel sinks are beautiful, but they come with a few honest trade-offs. Almost all of them are solved at the planning stage.
| Downside | Why it happens | How to avoid it |
|---|---|---|
| Splashing | The faucet is too high, too short or aims at the side of the bowl | Line the faucet up with the bowl and pick a spout height and reach that land the stream on the drain |
| Rim too high | The bowl sits on a standard height vanity | Choose a lower vanity or a shallower bowl |
| Cleaning around the base | Water and dust collect where the bowl meets the counter | Keep a neat silicone line and wipe the base when you wipe the bowl |
| Less counter space | The bowl sits on the counter instead of in it | Choose an oval or a smaller bowl on narrow vanities |
One worry you can drop with brass: a metal bowl will not chip or crack the way a ceramic or glass vessel can.
How do you care for an unlacquered brass vessel sink?
Most of our brass vessel sinks carry no lacquer, so they are a living finish. A bright polished bowl will slowly mellow to a warm amber or aged gold patina with use, and an aged finish will keep deepening.
- Rinse and wipe the bowl dry after use.
- Wash with mild soap and a soft cloth.
- Avoid bleach and abrasive pads.
- Polish with a gentle brass cleaner whenever you want the shine back.
Our Care and Patina Guide has the full routine, and how to clean a brass sink without stripping the patina covers deeper cleaning step by step. If you are curious how the color changes over time, see what unlacquered brass looks like after 1 month, 1 year and 5 years.

Frequently asked questions
Can I put a vessel sink on a standard height vanity?
You can, but the rim will sit higher by the full height of the bowl. A 5.5 inch bowl on a 34 inch vanity puts the rim at about 39.5 inches, which many people find too tall. A shallower bowl or a lower vanity fixes this.
Do brass vessel sinks come with a drain?
It depends on the sink. The Meknes Brass Vessel Sink includes a drain, while sinks such as the Hammered Round Brass Vessel Sink and the 16.5 inch round countertop sink offer a matching push-up drain as an option. Each product page lists what is included.
Are vessel sinks messy?
They do not have to be. Most mess comes from a faucet that sends water at the side of the bowl or drops it from too high, and from water left around the base. Aim the stream at the drain and wipe the base when you wipe the bowl.
Is your brass lead-free?
Yes. The brass we use for our sinks is lead-free.
Will an unlacquered brass vessel sink tarnish?
Yes, it will darken gradually into a warm patina, because there is no lacquer sealing the metal. If you prefer it bright, a gentle brass polish restores the shine whenever you like.
Are your brass vessel sinks in stock or made to order?
The Meknes Brass Vessel Sink is in stock and ships from our New Jersey warehouse. Most of our other vessel sinks are handcrafted to order in Morocco, with lead times of about one to three weeks depending on the product. Custom sizes are available on request.
Find your brass vessel sink
Round, oval, hammered and engraved bowls, handcrafted by artisans in Fes, Morocco.
Shop bathroom and vessel sinks →Custom sizes available on request. Every sink is shaped by hand, so no two are exactly alike.



